evunit

This is a unit testing application for Game Boy roms. It only contains a CPU emulator; no PPU, memory mapper, or I/O. By using real binaries as input, you can run unit tests on your finished ROM without any need to rebuild.

The command-line tool loads test configurations from TOML files. You can also use it as a Rust library, and configure your tests from Rust code.

Changelog

Installing

cargo install evunit

Configuring a test

Within the test config you can create a heading for each test you want to run, and assign default and expected values for registers. The first heading (for example, add-one) determines the initial state, while the ".result" heading (for example, add-one.result) describes the expected result. If the expected result does not match the final state, the test will fail.

[add-one]
b = 1
[add-one.result]
a = 2

[add-two]
b = 2
[add-two.result]
a = 3

You can assign any cpu register to an integer. In addition, 16-bit registers may be assigned a quoted label if a symfile is loaded. To determine which function should run in each test, assign a label to pc. Possible registers are:

• a
• b
• c
• d
• e
• h
• l
• bc
• de
• hl
• pc
• sp

In addition the flags can be assigned to either true or false. Possible flags are:

• f.z
• f.n
• f.h
• f.c

Note that the flags must be quoted in the config file because of the dot:

"f.z" = false

Finally, memory can be assigned a value in the config file by surrounding a label name in square brackets. You can either assign an 8-bit integer, a string, or an array of either. Like the flags, memory addresses must be quoted because of the square brackets:

# Writes a string to wString, followed by a 0
"[wString]" = ["Hello, world!", 0]

Global configurations

Sometimes you have configurations which should apply to all tests, like a global variable or the stack pointer. Any configurations at the top of the file (before a heading) are global and apply to all tests.

sp = "wStack.end"

[my-test]
pc = "MyTest"
a = 42
[my-test.result]
b = 42

If the test result is absent, the test will always pass unless it crashes.

Creating an exhaustive set of tests by hand might be tedious, so remember that you an always generate tests in Rust by using evunit as a library:.

use evunit::prelude::*;
use std::{path::Path, process::exit};

let rom = "bin.gb";
let sym = Some(Path::new("bin.sym"));
let symfile = read_symfile(sym);

let mut tests = Vec::new();

for i in 0..8 {
	let mut test = TestConfig::new(format!("my-test{i}"));

	// Initial state
	test.initial = Registers::new()
		.with_pc(symfile["GetBitA"].0 as u16)
		.with_a(i);

	// Expected state
	test.result = Some(Registers::new()
		.with_a(i));

	tests.push(test);
}

let result = run_tests(&rom, &tests, SilenceLevel::Passing);

if result.is_err() {
	exit(1);
}

Then pipe this into evunit. You can use - to read from stdin.

./config_generator | evunit -c - bin/rom.gb

And you can always use cat to add a handwritten file into the mix.

./config_generator | cat config.toml - | evunit -c - bin/rom.gb

Terminating a test

A test is complete when either a crash address is reached, the test times out, or pc is equal to the caller specified in the config file (default is 0xFFFF). evunit pushes the caller value to the stack before running your test, meaning that in most scenarios a ret will end the test. When the caller value is successfully reached, evunit checks to see if the result matches what was expected.

Configuration options

In addition to registers, there are a few other options you can configure. All of these can be configured globally as well as per-test.

caller

Sets the caller address. This address is pushed to the stack when a test begins, allowing ret to end the test.

caller = "Main"

By default, caller is set to 0xFFFF.

crash

Marks an address as a "crash", causing the test to fail if pc reaches it. This is useful for crash handler functions such as rst $38

crash = 0x38

An array of values can also be used.

crash = [0x38, "crash"]

enable-breakpoints

Enables or disables printing register info after executing ld b, b and ld d, d. Enabled by default. This configuration can only be used globally.

enable-breakpoints = true
enable-breakpoints = false

exit

Marks an address as an "exit", causing the test to end if pc reaches it. The results will then be verified.

exit = "SomeFunction.exit"

An array of values can also be used.

timeout

Sets the maximum number of cycles before a test fails. This is useful if you have code that tends to get stuck in infinite loops, or code which can take an extremely long time to complete. The default value is 65536.

timeout = 65536

Diagnosing failures

When a test fails, it outputs some cpu registers depending on the failure reason to help you diagnose the issue. However, sometimes you need to check the state of memory as well; this can be accomplished with the --dump-dir (-d) flag. Pass a directory to this flag and when any test fails a text dump of memory will be placed in the provided directory.

evunit -c fail.toml -d dump/ rom.gb

The dump is simply a giant list of bytes, with headers for each memory type:

[WRAM 0]
0xc000: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0xc010: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0xc020: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0xc030: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0xc040: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0xc050: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0xc060: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
...